Detroit Diesel · Series 71 · The Screaming Jimmy

Detroit 6-71 Oil: SAE 40, CF-2 & Capacity

Detroit 6-71 oil is a two-stroke decision, not a modern truck-oil decision. The right oil is a straight SAE 40 that meets Detroit’s low-ash limits, with a multigrade only where Detroit allows it for cold starts on land. The same rules apply to the V-block 6V-71.

Run SAE 40 with API CF-2 performance that meets Detroit’s Type 1 limits: 1.0% sulfated ash maximum and 7.0 TBN minimum. In cold land service, where Detroit allows a 15W-40 with at least 3.70 cP HTHS, the Red Seal tech pick is AMSOIL Signature Series Max-Duty 15W-40 (DME). Marine 6-71s stay on SAE 40, or SAE 50 if the engine runs above 200°F (93°C) coolant-out.

Last reviewed November 7, 2026 · Based on Detroit Diesel 7SE270 (January 2004), API category guidance and AMSOIL data sheets G3467, G3468 and G473.

SAE 40
Normal grade
CF-2
Two-stroke category

1.0%
Max sulfated ash
7.0
Min TBN

≈28
6-71 oil qt (published)
426
Cu in · ≈7.0 L
Oil Spec

Detroit 6-71 Oil Spec: Detroit’s Type 1 Limits

The inline 6-71 and the V6 6V-71 belong to Detroit’s classic two-stroke Series 71 family: same 71 cu in per cylinder, same 426 cu in total. Both are different engines from the four-stroke Series 60 and the modern DD13, DD15 and DD16. Modern Class 8 oil advice does not carry over. Whether one sits in an old tractor-trailer, a transport truck, a coach, a generator set or a boat, the oil has to meet Detroit’s two-stroke limits.

Source: Detroit Diesel 7SE270 (January 2004), section 2.2 and table notes.
RequirementLimitNote
ViscositySAE 40Normal grade, land and marine
PerformanceAPI CF-2Two-stroke category; obsolete for licensing
Sulfated ash1.0% maxType 1 oil
Total Base Number7.0 minType 1 oil
HTHS (multigrade)3.70 cP minOnly where a multigrade is permitted
FuelBelow 0.5% sulfurType 1 is primary; covers today’s ULSD

CF-2 is an obsolete API category. API no longer licenses CF-2 and directs owners of two-stroke engines to the engine manufacturer for current lubrication recommendations. Treat a CF-2 claim on a data sheet as a performance statement, not a current API licence. Read API’s category guidance.

⚠ Don’t buy by the CK-4 donut. A CK-4 or FA-4 label says nothing about two-stroke suitability. Oils built for DPF-equipped heavy-duty trucks are not automatically right for a 6-71. Check for CF-2 performance, the ash and TBN limits, and the grade Detroit allows for your service.

6-71 vs 6V-71

6-71 vs 6V-71: Inline or V-Block?

Same Series 71 family: 4.25 in bore, 5 in stroke, 426 cu in, two-stroke with a gear-driven Roots blower. Same oil. What changes is the shape of the engine, and that decided where each one ended up.

Base ratings from the Detroit Diesel Series 71 specification table (Wikipedia). Actual ratings vary by injector, turbo and application.
Factor6-71 inline6V-71 V-block
Introduced19381957
LayoutInline six, one headV6, one head per bank
Length × width × height54 × 29 × 39 in41 × 39 × 48 in
Rated speed (non-turbo)2,100 rpm2,100 rpm
Power (non-turbo)170–228 hp228 hp
Power (turbo)275–285 hp (6-71T)262 hp (6V-71T)
Torque (turbo)762–801 lb-ft @ 1,400 rpm725 lb-ft @ 1,600 rpm

Inline 6-71: Narrow, Low, Strong

  • Fits narrow, low spaces. At 29 in wide and 39 in tall it suits narrow engine bays, and Detroit built a lay-down “pancake” version (6L-71 / 6N-71) for underfloor bus mounts.
  • One cylinder head. One head and one set of head gaskets on a top-end job.
  • More turbo output on paper. The 6-71T is rated higher than the 6V-71T in both horsepower and torque, with peak torque lower in the rev range.
  • Weakness: length. At 54 in it needs a long engine bay or engine room.

6V-71: Short and Compact

  • 13 inches shorter. At 41 in long it fits short engine compartments, set-back installs and short boat engine rooms where an inline won’t go.
  • Same displacement, smaller box. 426 cu in in a block that sits close to square.
  • Weakness: width and height. 39 in wide and 48 in tall, so it needs headroom and side clearance.
  • Weakness: two heads. Two of everything on the top end, and lower published turbo ratings than the inline.

Does the V rev higher? Not on paper. Both non-turbo versions are rated at 2,100 rpm with the same bore and stroke. It may sound like it, but that’s the Screaming Jimmy effect, explained below.

For oil, none of this changes anything. Both engines run the same SAE 40, CF-2 and Type 1 limits. Only the oil pan, and so the refill, is different.

The Screaming Jimmy

Why the 6-71 Is Called the Screaming Jimmy

Anyone who rode a Greyhound, worked a tug deck or ran a GMC tractor-trailer in the ’60s and ’70s knows the sound before they know the name. It’s a high, hard wail that tells the whole yard a Detroit two-stroke is working. The name has two halves, and both are straight from the engine.

“Jimmy” = GM

Detroit Diesel was General Motors’ diesel division. Say “GM” fast enough and you get “Jimmy,” the same slang behind GMC trucks. For almost two decades the Detroit two-stroke was exclusive to GMC trucks and coaches, so the engine and the badge shared the nickname.

“Screaming” = Two-Stroke + Blower

A two-stroke fires every cylinder on every revolution, twice as often as a four-stroke. At 2,100 rpm a Jimmy sounds like it’s turning twice that. Layer on the whine of the gear-driven Roots blower forcing air through the ports, and you get the scream.

1938
The 6-71 Arrives

Introduced as the flagship of the new Series 71, then in GMC trucks from 1939.

WWII
Built by the Hundred Thousand

Roughly 100,000 built in the war years for landing craft, ships, tanks and trucks.

1957
The V-Block Joins

The 6V-71 brings the same 426 cu in in a shorter package, followed by the 8V, 12V and 16V-71.

The whole Detroit two-stroke family wears the name, but the 6-71 and 6V-71 are the engines most people picture. The 12V-71 even earned its own nickname, the “Buzzin’ Dozen.” Tightening emissions rules ended on-highway sales in 1995, but parts and factory rebuilds are still available, and thousands of Jimmys still run in boats, buses, generators and restored trucks.

Found a Jimmy on Marketplace? Ask what oil it has been running. A CK-4 multigrade in a marine engine, or no answer at all, tells you how it has been looked after. Expect some oil on the outside: Detroits are known for it, so judge the trend, not one drip. Then pull a sample at the first oil change. Coolant, fuel dilution and wear metals in the report tell you what you bought before you find out the expensive way.

Get an Oil Analysis Kit →
By Service

Land, Cold Start or Marine

Detroit sets the grade by how the engine is used. Record the model and serial number, any repower history and the oil pan arrangement first: on an older truck, the model year does not reliably identify the engine in it.

SAE 40
Normal Land Service
  • CategoryCF-2
  • Ash / TBN≤1.0% / ≥7.0
  • AMSOIL optionNone listed
15W-40
Cold Land Starts
  • WhenDetroit allows it
  • HTHS≥3.70 cP
  • AMSOIL optionDME · ADP
SAE 40 / 50
Marine
  • MultigradesExcluded
  • SAE 50>200°F coolant-out
  • AMSOIL optionNone

SAE 30 is also permitted for cold land starts. In every case, go back to SAE 40 when conditions allow.

What to Buy

Best AMSOIL Oil for the Detroit 6-71

For normal service, AMSOIL does not list a straight SAE 40 two-stroke diesel oil. Buy a CF-2 SAE 40 from your lubricant supplier and check its published ash and TBN against the limits above. AMSOIL comes in for cold land starts, where Detroit allows a 15W-40.

Cold Land Starts · Full Synthetic
AMSOIL Heavy-Duty Synthetic Diesel Oil
15W-40 · ADP · API CF-2 listed
  • Sulfated ash 1.0% (typical), at Detroit’s limit
  • TBN 10.2 against a 7.0 minimum
  • HTHS 4.7 cP against a 3.70 minimum
  • Lower-cost full synthetic for the same permitted use
Shop ADP 15W-40 →
CheckDetroit limitDME 15W-40ADP 15W-40
Two-stroke categoryCF-2 performanceCF-2 listedCF-2 listed
Sulfated ash1.0% max1.0%1.0%
TBN7.0 min10.110.2
HTHSMultigrade only3.70 cP min4.5 cP4.7 cP

Typical values from AMSOIL data sheets G3467 (DME) and G3468 (ADP), checked against Detroit 7SE270. Not shown: AMSOIL Commercial-Grade (SBDF) does not list CF-2. AMSOIL Heavy-Duty Diesel & Marine (AME) lists CF-2 but publishes no sulfated-ash value, so it can’t be checked against Detroit’s 1.0% limit.

Capacity

Detroit 6-71 Oil Capacity

Refill capacity depends on the oil pan, and 71 Series engines went into everything from trucks and coaches to boats and gensets, so pans vary. The dipstick is the final word. Detroit’s rule: never let the level drop below the LOW mark, and nothing is gained by filling above FULL. Check it with the engine stopped at least five minutes so oil drains back to the pan. Watch the units: US quarts, Imperial quarts and litres are different measures.

Fill rule and filter allowance: Detroit Diesel Inline 71 service manual 6SE177, Section 4.6, and V-71 service manual 6SE193. The 6-71 refill figure is as published by Diesel Pro Power, a Detroit parts supplier, not a Detroit specification.
Item6-71 inline6V-71 V6
Fill toDipstick FULL markDipstick FULL mark
Typical refill≈28 qt (7 gal, 26.5 L)Varies by oil pan
Filter changeAbout 2 qt more (Detroit)
Never run belowDipstick LOW mark

How much to buy: have about 8 gallons on hand for a 6-71 change with filters, and top up to the FULL mark. Running DME in permitted cold land service? Two AMSOIL Twin Packs (DMETP-CA, 10 US gallons or 40 qt) cover a full change on a 6-71 or 6V-71, with oil left for top-ups.

Before the Oil Change

  • Confirm the oil pan and filter part numbers.
  • Check whether the capacity includes new filters.
  • Follow the manual’s fill and level-check procedure.
  • Record mileage, hours, date and oil used.

Build a Useful Service History

Log top-up quantities alongside oil changes, and keep hours with mileage where you have them. Two-strokes use some oil by design, so the trend matters more than any single reading. If consumption changes, find out why instead of masking it with a different oil.

Detroit said it first: set the interval on data. The 1974 Inline 71 manual starts new engines on a 150-hour oil change (about 4,500 highway miles, or 2,500 in city service), then has owners adjust it with experience and analysis of the drained oil. That’s still the right method. A sample at every change shows fuel dilution, coolant, dirt and wear metals in the report before they show up as a rebuild.

Get an Oil Analysis Kit →
FAQ

Detroit 6-71 Oil FAQ

What oil does a Detroit 6-71 take?

SAE 40 with API CF-2 performance that meets Detroit’s Type 1 limits: sulfated ash 1.0% maximum and TBN 7.0 minimum. Detroit allows a qualifying 15W-40 for cold starts on land, but not in marine service.

Can I run 15W-40 in a Detroit 6-71?

Only in land service where cold starting calls for it, and only an oil with CF-2 performance, at least 3.70 cP HTHS, and ash and TBN within Detroit’s limits. Go back to SAE 40 when conditions allow. Detroit excludes multigrades in marine two-strokes.

Does AMSOIL make an oil for the Detroit 6-71?

Not for normal service: AMSOIL does not list a straight SAE 40 two-stroke diesel oil. For permitted cold-weather land use, AMSOIL Signature Series Max-Duty 15W-40 (DME) and Heavy-Duty Synthetic 15W-40 (ADP) both list API CF-2, with 1.0% sulfated ash and TBN above 10.

Does CF-2 being obsolete mean I should use CK-4?

No. API lists CF-2 as obsolete but directs two-stroke owners to the engine manufacturer for current recommendations. A CK-4 label does not establish Detroit two-stroke suitability.

Is SAE 40 the same as 15W-40?

No. SAE 40 is a monograde and 15W-40 is a multigrade. Sharing the same hot-viscosity grade does not make them interchangeable in a two-stroke Detroit.

Does the 6V-71 take the same oil as the 6-71?

Yes. The 6V-71 is the V6 version of the same Series 71 two-stroke, with the same 426 cu in, so the same SAE 40, CF-2 and Type 1 limits apply. Its oil pan is different, so use the 6V-71 row in the capacity table.

Why is the Detroit 6-71 called the Screaming Jimmy?

“Jimmy” comes from GM: Detroit Diesel was General Motors’ diesel division, and the engines powered GMC trucks and coaches. “Screaming” comes from the sound. A two-stroke fires every cylinder on every revolution, so at 2,100 rpm it sounds like it’s turning twice that, and the gear-driven Roots blower adds a high whine on top.

Does the 6V-71 rev higher than the 6-71?

Not on paper. Both non-turbo versions are rated at 2,100 rpm with the same 4.25 in bore and 5 in stroke. The 6V-71’s “Screaming Jimmy” nickname comes from its high-pitched sound at 2,100 rpm, not a higher rev limit. The real differences are shape: the V is 13 inches shorter, but wider and taller.

How much oil does a Detroit 6-71 or 6V-71 hold?

Fill either engine to the FULL mark on the dipstick: oil pans vary by installation, and Detroit’s V-71 manual gives no fixed figure. The inline 6-71 is commonly listed at about 28 quarts (7 gallons), and Detroit allows about 2 quarts more at a filter change. Two AMSOIL Twin Packs (10 gallons) cover a full change on either engine.

Technical References

  1. Detroit Diesel 7SE270, January 2004 — two-stroke lubricant requirements and viscosity notes, pages 2-2 through 2-4.
  2. API oil categories — CF-2 status and manufacturer guidance.
  3. AMSOIL data sheets G3467 (Signature Series Max-Duty, DME) and G3468 (Heavy-Duty Synthetic, ADP) — listed specifications and typical properties.
  4. AMSOIL data sheet G473 — Heavy-Duty Diesel & Marine (AME).
  5. Detroit Diesel Series Inline 71 service manual 6SE177 (1974) — Section 4.6 oil level and filter allowance; Section 13.3 lubricating oil and oil change guidance.
  6. Detroit Diesel Series V-71 service manual 6SE193 (1989) — 6V-71 refill instruction (fill to the dipstick).
  7. Curbside Classic: 1939 GMC and the “Jimmy” Detroit Diesel — GMC exclusivity, the nickname, end of on-highway sales.
  8. Yachting: “Jimmy” Rules, Detroit Diesel 6-71 — Roots blower sound, wartime production, engines still in service.
  9. Detroit Diesel Series 71 (Wikipedia) — 6-71 and 6V-71 dimensions, ratings and history.
  10. Diesel Pro Power: Detroit 6-71 information — published land 6-71 oil capacity.
  11. MAHLE heavy-duty engine catalogue — 6-71 configuration and displacement.

Detroit Diesel and AMSOIL trademarks belong to their respective owners. Their use does not imply affiliation or endorsement.

Scroll to Top